|
Language: EN | 中文 |

Share:


FS2000

Quantity: In Stock

 

 

 

Product outline

The best solution for OK/NOK judgment of press fitting and caulking application !! High responsiveness of 5kHz to fully utilize the performance of Super Cell !!
A fluctuation of force is shown as a waveform.

FS2000 is a digital indicator integrated with a strain gauge sensor that can display physical quantities such as pressure, load and torque in waveforms. It is able to visually capture in waveforms the fluctuations in physical quantities which are difficult to capture by only numerical values. With a 25000 times per second for high-speed processing, it is also ideal for narrow value fluctuations and comes equipped with a HI/LO limit comparison function, various hold functions and judgment function. FS2000 can be used in a wide-range of applications such as in control systems used in production control, automatic devices or testers.

OK/NOK judgment with 2ch sensor inputs !!

Two-dimensional OK/NOK judgement can be performed with a load cell and displacement sensor.

Comparison & hold function by waveform display

■ Waveform comparison
This function compares the actual measurement waveform against the setup High/Low limit waveforms and will give out an NOK judgment when any of the point exceeded the preset High/Low limit waveforms.
■ Multi-point judgment
OK/NOK judgment can be performed on multi points in one process. (e.g. The start point and end point of press fitting can be judged respectively.)(Max. 5 points)

Example of use

Improved usability

4.3 inch wide display provides excellent visibility.
Main display configuration can be selected to keep it as simple as possible by eliminating unnecessary information.

Trend display is helpful for preventive maintenance

Trend of the zero-point shift and hold values can be monitored to find any irregularities for preventing breakdown of machines.
In addition, the master settings can be registered so that operator can compare with the current settings to see if there are any differences.

Changed setting items are highlighted!

Master and current set values are listed up for checking the changed setting items easily.
Set values can be edited directly on the list without going into each setting menu.
* Except for waveform comparison settings.

Saved measured data (waveform) on the SD card can be displayed afterwards

Measured data and set values can be saved in the SD card. Data can be converted to CSV format easily for editing with Microsoft Excel.

 

 

Specifications

Sensor input
Sensor input for load (Fixed as strain gauge input)(6-wire)
Excitation voltage DC 2.5, 5, 10V±10% (depending on settings)
Output current: Within 30mA
Signal input range -2.0mV/V to +2.0mV/V
Accuracy Non-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input)
Zero drift: Within 0.1μV/℃ RTI
Gain drift: Within 15ppm/℃
Low-pass filter Selectable from 10 to 10kHz(at A/D converter speed 25000 times/sec)
Selectable from 2 to 2kHz(at A/D converter speed 5000 times/sec)
A/D converter Speed: Selectable from 25000 times/sec., 5000 times/sec.
Resolution: 24bit (binary)
Sensor input for displacement
Pulse input(Line driver)
Max. input frequency 1MHz
Internal count range Approx. 1,000,000
Adaptable rotary encoder Output: Incremental type 2-phase output (A/B signal output)
Also capable of single-phase output
(A-phase input used. All pulses are counted as in the plus direction.)
Output stage circuit specification: Line driver (Based on RS-422)
Sensor input(Multisensor input:MLT or MLT2)
Sensor input for load (Fixed as strain gauge input)(6-wire)
Excitation voltage DC 2.5, 5, 10V±10% (depending on settings)
Output current: Within 30mA
Signal input range -2.0mV/V to +2.0mV/V
Accuracy Non-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input)
Zero drift: Within 0.1μV/℃ RTI
Gain drift: Within 15ppm/℃
Low-pass filter Selectable from 10 to 10kHz(at A/D converter speed 25000 times/sec)
Selectable from 2 to 2kHz(at A/D converter speed 5000 times/sec)
A/D converter Speed: Selectable from 25000 times/sec., 5000 times/sec.
Resolution: 24bit (binary)
Sensor input for displacement
Pulse input (Open collector)[MLT]
Max. input frequency 1MHz
Internal count range Approx. 1,000,000
Adaptable rotary encoder Output: Incremental type 2-phase output (A/B signal output)
Also capable of single-phase output
(A-phase input used. All pulses are counted as in the plus direction.)
Output stage circuit specification: Open collector (built in pull-up resistor)
Sensor input for displacement
Pulse input(Line driver)[MLT2]
Max. input frequency 1MHz
Internal count range Approx. 1,000,000
Adaptable rotary encoder Output: Incremental type 2-phase output (A/B signal output)
Also capable of single-phase output
(A-phase input used. All pulses are counted as in the plus direction.)
Output stage circuit specification: Line driver (Based on RS-422)
Voltage input
Signal input range -10 to +10V
Input impedance App. 1MΩ
Accuracy Non-linearity:Within 0.02%/FS ±1 digit (at 10V input)
Zero drift:Within 0.2mV/℃ RTI
Gain drift:Within 0.01%/℃
Low-pass filter Selectable from 10 to 10kHz(at A/D converter speed 25000 times/sec)
Selectable from 2 to 2kHz(at A/D converter speed 5000 times/sec)
A/D converter Speed:Selectable from 25000 times/sec, 5000 times/sec
Resolution:24bit Effective Resolution: Approx. 1/20000 against 10V
 
Analog voltage output Output level: Approx. 2V per 1.0mV/V input
Load resistance: 2kΩ or more
 
Display section
Display 4.3 inch TFT color LCD module
Display area: 95.0(W)×53.9(H) mm
Dot configuration: 480×272 dot
Display frequency Fixed at 3 times/sec.
 
COMP. & JUDGE. function
Multi point comparison mode
16ch
(setting values can be stored)
Capable of judging up to 5 hold points at the same time.
Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End
Waveform comparison mode
16ch
(setting values can be stored)
Compares the actually measured waveform against the preset Hi/Lo waveforms.
The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK.
 
Preventive maintenance support
Trend display Showing the trend of measurement data to help finding irregularities at early stage.
Statistics Using the latest 10000 measured data.
Displaying number of measurement, OK, NOK
Screen capture Saves screen capture data as bmp data.
Work name edit Work name can be edited and displayed for each Work No..
Setting list display Changed setting items comparing to master set values are highlighted.
User management Login ID and Password
 
External signal
Output signal 16 points
Hold judgment (load, displacement)/ Load overload/ Measurement complete/
Waveform comparison judgment/ Load & displacement OK/ CPU OK/
SD card OK/ Timing output 1,2
Output Type: Sink type/source type selectable.
(Source Type is option: [ISC])
Output transistor ON at signal ON.
To connect an input unit like a PLC, connect plus common for sink type, and minus common for source type.
Rated voltage: 30V
Rated current: 30mA
Input signal 16 points
Load digital zero/ Displacement adjustment/ Measurement start/
Measurement end/ HOLD1 to 5/ Reset/ Forcibly light up the backlight/
Touch panel lock/ Work change
Input type: Plus common/Minus common selectable.
(Minus common is option: [ISC])
To connect a transistor, connect NPN output type (sink type) for plus common and PNP output type (source type) for minus common.
 
Interface
Only one option can be installed.
USB USB interface
ODN DeviceNet interface (option)
CCL CC-Link interface (option)
EIP EtherNet/IP interface (option)
 
General performance
Power supply voltage DC24V (±15%)
Power consumption 6W typ
Operation condition Operation temperature: -10℃ to +40℃/ Storage temperature: -20℃ to +60℃
Humidity: 85% RH or less (non-condensing)
Dimensions 132(W)×98(H)×110(D) mm (Projections excluded)
Weight Approx. 1.0kg
 
Attachments
I/O connector (with cover) 1
Analog connector 1
Operating tool 1
SD card 1
Operation manual 1
DeviceNet connector (when DeviceNet option is selected) 1
CC-Link connector (when CC-Link option is selected) 1
 

Option

Model
ISC I/O source board
MLT Multisensor input
MLT2 Multisensor input
ODN DeviceNet interface
CCL CC-Link interface
EIP EtherNet/IP interface
 

Optional accessories

 

Model
CN71 CC-Link connector
CN72 Double row connector for CC-Link
CN77 Analog connector
CND01 DeviceNet connector
SD1G 1 GByte SD card
SD2G 2 GByte SD card
SD16G 16 GByte SD card
SD32G 32 GByte SD card
CA81-USB USB cable (A-miniB type) 1.8m
TSU03 DC lighting surge unit
 

Download

Product catalogue(PDF)
FS2000_catalogue(654 KB)



 Inquiry - FS2000